Lighting a Charcoal BBQ Grill Fast and Easy

The best as well as the easiest way to light charcoal briquettes is by using a charcoal chimney starter. This is an aluminum cylinder with a wooden handle on the outside and a metal shelf on the inside that separates the cylinder into to sections. The top section is about 2/3 the length of the cylinder and the bottom section is 1/3 the length of the cylinder. There are round holes surrounding the bottom 1/3 of the cylinder as well as holes inside on the shelf that separates the two sections.

To use the charcoal chimney starter, you need 2 to 3 sheets of newspaper. Wad or roll the sheets together loosely into a long cylinder. I don't wrap it too tight so that air can circulate while it is burning. Curl the the sheets into a donut shape with a hole in the center. Fit the paper donut into the bottom of the chimney starter. Try to have a few stray pieces of paper sticking out of the holes. This makes it easier to light. If you want you can use paraffin cubes either bought in the store or made out of something like a cardboard egg crate you buy your eggs in.

Fill the top section of the cylinder with charcoal. I prefer to use briquettes in the chimney starter. Lump charcoal burns too quickly. Place the chimney starter on the floor or charcoal shelf of your bbq grill and light the newspaper through the holes on the bottom of the charcoal chimney starter. The charcoal lights fairly fast and should be ready in about 15 minutes. Lump charcoal is a lot faster to start but also burns out faster, so I don't use it in the chimney starter. The charcoal is ready when you see a coating of white ash over almost all of the charcoals.

When the coals are ready, carefully poor the coals into the grill and spread them evenly around the grill bed. Remember to safely place the very hot charcoal chimney starter away from pets and children so they don't get burned. Also, don't put the hot chimney starter on the grass because it can cause a fire.

A second method to light the charcoals is with paraffin cubes bought at a store or made at home with cardboard egg crates. Place a few paraffin cubes in the middle of your grill bed or charcoal grate. Then build a pyramid of charcoal briquettes over and around the paraffin cubes. Light the cube and when all the briquettes are evenly lit and covered with ash spread them evenly out around the grill bed.

I don't like or recommend starter fluid readily available in stores. These fluids can impart a taste to the charcoal that I don't like and I prefer a more natural non chemical way to start my fire.

A chimney starter holds about 90 to 100 briquettes. This should cover 2/3 of the area of a standard 22 1/2 inch standard charcoal kettle grill like the commonly used Webber kettle grill. It is important to use the right amount of briquettes so that you get an even heat. The charcoal briquettes should extend a minimum of 4 inches in every direction beyond whatever food you are cooking. This will allow an even heat and let your food cook evenly.

For more tips and great information to make your next barbecue memorable visit the bbq-expert.com We show you what to look for in your next bbq grill, how to light a charcoal bbq grill properly and everything in between.

Water Stains On Shingles

Stairway Safety - Stair Construction Tips

If you've built as many stairways as I have, this is a very simple question to answer. Should I use 2 x 12 or 3 x 12 for my stair treads? Without a doubt I would use the 3 x 12 for a couple of reasons.

The thickness of the three by material gives it some additional strength and that strength could prevent someone from falling through the stairway and getting injured. Visually looking at the 3 x 12 it gives you the illusion that the stairway is safe. Once you start walking up the stairway and the stairs seem solid and well constructed, it takes the illusion and makes it a reality.

If you're walking up a poorly constructed stairway every day, not only is it a safety problem but it takes a little bit of effort as you walk up the stairway, holding on to the hand rail with a death grip, this can easily wear someone out physically and mentally, over time. Stairways should be constructed and maintained with safety as the main priority.

If you've ever walked up and older stairway that was built using 2 x 12 for the stair treads, you probably know what I'm talking about. Walking up and down the stairway, while the stair treads are moving, does not give you a strong sense that the stairway is safe. And of course sometimes the stairway isn't.

For example if you have a 3 inch knot in a 2 x 12 stair tread, over time as the wood expands and contracts, the knot can loosen up and fall out of the stair tread, often creating a weak spot in the step. With a thicker stair tread, it will take a little more expanding and contracting to create a weak spot in the stair step.

If you're building a stairway wider than 36 inches, with no center stair stringers to support the stairway, I would suggest using a 3 x 12 or 4 x 12 for your stair treads. 2 x 12 should not be used for stair treads on any staircase wider than 36 inches.

If you choose to use 2 x 12 for your stair treads, select premium grade lumber for safety. Try to avoid using center cut building materials and 2 x 12 with knots larger than an inch and a half. Large knots are one of the biggest problems in construction safety.

Greg Vanden Berge is working on the internet to promote the education for creating simple to follow guides and home building books to help professional building contractors as well as the weekend warriors. He has just finished a home buyers guide to take some of the frustration out of home shopping.

Learn more about the parts of the stairway, whether you're a experienced carpenter or homeowner. Stair building does not necessarily have to be as complicated as most people make it out to be. There's also a book on how to build straight stairs that can save you a lot of frustration, if you've never built a stairway before. Visit the website.

Moisture On Vapor Barrier

Kitchen Cabinet Basics - What to Know Before You Remodel

If you are considering a "Full Kitchen Remodel" then the first place you will want to start (with regard to material choices) is with your cabinets. Cabinets set the tone for the style and color scheme of your entire kitchen. Answering the questions below will get you on the right track.

Design Styles: The most common design styles these days include Shaker, Modern Contemporary, Traditional, Casual Country and Eclectic. Determining the style will direct you to the wood species that work best.

Door Styles: There are basically three door styles to choose from: Raised Panel, Recessed Panel and Slab. With regard to the raised and recessed doors, you will then need to choose from square, arch or cathedral style.

Types of Wood: Cabinets are made from a multitude of wood species; however the most common these days are (in order of hardness and durability):

Oak, Hickory, Mahogany, Laminates
Maple, Cherry, Birch, Pine
Alder, Poplar

Cabinet Quality: The qualities of cabinets available range from all solid wood construction, partial wood construction with plywood veneer, particle board and veneer and (at the lower end of the spectrum) particle board and photo finish and laminates: Of course the prices range (with all wood construction) from very expensive to very inexpensive (photo finish) or laminate construction. While the old adage "You Get What You Pay For" holds true in most cases, there are a number of ways to reduce your overall cost and still have the quality and look you want. For instance, you can have solid wood fronts and on the exposed ends (doors, drawers and face) and use plywood or particle board on the sides and backs (which are not seen). This can save you thousands of dollars.

Other Cabinet Options: The final choices that are worthy of note are the additional options for your cabinets. These include Lazy Susans, waste basket cabinets, spice racks, wine racks, pull-out trays (instead of fixed shelving) "soft close" drawer hardware, dove-tail drawer or butt-joint drawer construction and (for upper cabinets) crown molding, under mount light molding etc. Glass doors (typically on upper cabinets) also lend a certain 'jene se qua' to the final look.

Cabinet Finishes: Yet another consideration is the finishes available: They are laminates, painted and stained. Regarding stain finishes: You can choose from the standard finishes and (if so inclined) add a "glaze finish" to further accent the wood grain and design of the cabinetry. *** Note: When you choose to add a glaze finish, there will be additional costs and (equally important) additional production time. Glazes can increase your cabinet expense from 6% to 20% and add one to two weeks on to the normal production schedule.

Hardware: The sky is the limit with regard to choices of colors, styles and designs of knob and handles. You can literally spend hours online looking at designs and styles. *** Note: Remember to add this into your cabinet budget from the outset as prices range from $3 or $4 dollars for simple knobs & handles to as much as $20 or more for the more ornate ones! Do you homework and research to find the type you want and the lowest cost producer of same.

In conclusion, remodeling your kitchen can be an exciting and rewarding endeavor and add value to your home. With proper planning, you will get the result you want within the budget you wish to keep. Perform your "due diligence" and you will have a final result for you and your family to enjoy for years to come! Good Luck.

If this article has been helpful and you would like more information on our kitchen remodeling services, please visit our website at http://www.pdremodelingsandiego.com

For a no obligation consultation, simply send us an e-mail at sfrick@pdr-sd.com or call us at (858) 560-0444. We service all of San Diego county and have been in business over 22 years.

How to Install Ceramic Tile - Proven Steps to Success

You can quickly learn how to install ceramic tile and have stunning success with your project. Sure installing tile is usually left to the pros. But with the right tips, most people can build beautiful surfaces. It's just a matter of getting the right tools and learning how to prepare the surfaces and put the tile in place. Following are the four basic steps for getting tile installed the right way.

Gathering the materials is the first step. Now materials includes getting the few basic tools required for tile installation. There are just a few special tools required. The most important tools you don't already have are the tile cutting tools. That would include tile nippers, maybe a tile cutter board and usually a tile saw. You can rent a saw or start with a very inexpensive saw too.

The other part of gathering materials is deciding on the tile you will use and how much tile you need. That may be the hardest part of the whole project. That's because you have so many tile choices. After you decide how much tile you need, you'll know how much tile adhesive and grout you'll need too. Your tile supplier can help you figure quantities of all the materials. Once you have your materials you're ready to get started with the installing.

An important preparation step is getting the base for the tile solid and clean. A surface that moves will cause cracked tiles. Often the easiest way to get a solid smooth surface is to put down cement board. But that's not necessary since tile can be installed over many different materials. Once you have your materials and your surface preparation done, the actual installation is not very hard.

Laying the first tile is the hardest part. That's because the position of the first tile determines how much cutting of tiles you'll do. It also determines how straight the joint lines will be. Getting the tiles lined up correctly will make for a neat installation. The best way to get the lines straight is to use your chalk line early and often. Actually setting the tiles involves some art. Setting tile is easiest if you gently twist the tiles into position. You don't want to drop the tiles into place or slide the tile into place either. Make sure you have enough mud on the tile so you have a little extra so you can bump the individual piece into place.

Once the tiles are in place, the grouting of the joints goes quickly. Grout does come in several types. Whether you choose sanded or unsanded grout depends on the size of the joint. Another option is using epoxy grout where the tile is in a constantly wet place. After the grout sets briefly, it is easily cleaned to finish the job.

You can learn how to install ceramic tile with the right instruction and some practice. There's no reason why you can't do a professional looking job on your first project. There are quite a few tricks to learn to make it easier to lay tile.

Video tutorials showing how to install ceramic tile can be found at our website.

Al Bullington invites you to visit http://InstallingCeramicTile.net for answers to your tile questions.

Learning About the Dumbwaiter

Dumbwaiters have been used for many years to make tasks around the home much easier. They are a type of small-scale elevator, which can usually support around a hundred pounds. Some lifts that are installed in businesses can support much more weight than this though. Often a commercial dumbwaiter will support over seven-hundred pounds. Dumbwaiters that are intended for use in homes are usually much smaller though. For the home, you can go with a manual or electric dumbwaiter.

The manual dumbwaiter has been used for thousands of years. At their simplest, they are just a platform and a rope. The rope is used to raise and lower the platform. While it would be possible to simply throw the rope over a rafter, most people use a pulley to help reduce the effort it takes to raise the platform. There are also several more advanced designs that move along tracks and use screws or gears. Most manual dumbwaiters will drop if you let go of the rope, but some are designed with safety stops so that you can let go of the rope if you become tired or need a break.

Some people still use manual dumbwaiters, but most choose to go with an electric dumbwaiter. These are much easier to use, because the only work you need to do is load it up and push a call button. These lifts usually move along a track that helps keep the track much more stable than most manual dumbwaiters.

They also have many safety features built in, that prevent damage to the lift, but also keep those that use it safe. The main safety feature these lifts have is automatically locking doors. The shaft of the dumbwaiter can sometimes be more than twenty feet long, which could prevent a fall risk. The doors on an electric lift are made so that as soon as the car moves away from the shaft opening, the doors lock. This means that it is not possible to open up the shaft way door, unless the dumbwaiter car is present.

The installation of an electric lift is usually able to be done in an afternoon, but it requires a good amount of technical understanding. Often a professional installation team will be used, but by purchasing a dumbwaiter kit that is easy to install, the process could be much easier, so in turn less expensive. One kit that is easy to install is the AmeriGlide Express. This comes with the drive system and lift already installed, so it drastically cuts down the time it takes to install the lift.

Aside from the obvious physical task of having to manually move a dumbwaiter, manual dumbwaiters also are not able to support anywhere near as much weight. Usually an electric dumbwaiter will support around a hundred pounds, but many support more than this, or can be upgraded to do so.

Installing one of these lifts in the home is an excellent way to increase productivity around the home. They will also often become something that helps to add value to the home after it is built, which is a very important consideration today.

Sean, a writer, knows much about lifting devices like the dumbwaiter. Around the home, these devices make it much easier to get the groceries to the kitchen or do laundry. They have countless applications and are also very popular commercially.

Learn more about these and other mobility aids at AmeriGlide.com, which is the leading distributor of stair lifts. A stair lift is a device that transports a person up the stairs. They usually attach directly to the staircase and can be installed easily by the homeowner. Cost wise, a stair lift will usually present a much more cost friendly solution to falls on the stairs.

Supercharge Your Water Heater

Have you ever had to stand shivering in the cold morning air waiting for hot water with your arm outstretched, fingers extended into the cold stream of water. It seems to take forever for the water to get hot. Speed up your hot water with a hot water circulating system.

Traditionally, if you had a hot water circulating system, it meant that you had a hot water pipe that ran in a big loop from the outlet of the water heater to each fixture one after the other, and then back to the inlet of the water heater through a small pump. By continuously pumping water through the loop you have instant hot water at every fixture.

This is very convenient. Hotels and motels have hot water circulating systems; otherwise it could take hours to get hot water with such long pipes as they have.

However, instant hot water is also very expensive. Not only do you have to pay for the energy to run the pump continuously for long periods of time or even full time, but you also have to pay for the heat energy being radiated into the environment from that big loop of hot water piping. The cost of heating the water is considerably more than the cost to run the pump.

There are a number of manufacturers producing hot water circulating systems that utilize the cold water line as the hot water return line.

Some of these pumping systems use small pumps that pump water very slowly, and are temperature controlled. The pump turns on when the water temperature drops below a set point, and then shuts off when the water temperature in the pipe reaches another set point. This keeps the water your entire piping system full of luke-warm water. The water is warmer near the water heater and colder the further you get from the water heater, but it is tepid through out the piping system.

Most folks don't really want the cold water pipe full of warm or tepid water. You don't get "Instant Hot Water" as the manufacturers claim. I think they should be honest and call them "Instant Tepid Water Systems". The Lang Auto-Circ and The Grundfos Comfort System are two such systems, and the Hot Water Lobster is another. The Hot Water Lobster doesn't have a pump, but relies on the fact that hot water rises, and the Lobster valve has to be substantially higher than the water heater for the system to work.

Unfortunately these systems consume much more energy since you are heating that big loop of piping and return line and its surroundings. The cost of the energy will far outweigh any monetary savings from the water conservation aspect.

Another class of systems that use the cold water line as the return line is the "Hot Water Demand Systems". These systems only pump the water to the fixture when hot water is "demanded" by the user. The pumping costs are small; typically demand systems use less than $2.00 per year in electricity costs. This is because they run for such a brief time, typically less than 1 minute per use.

When the user turns on the pump it runs until hot water reaches the fixture and then the pump automatically shuts off. The cold water line does not end up full of warm water.

With the demand system the energy consumed is no more than if the user just ran the tap as normal. Hot water is not being circulated. And since the hot water is not being circulated it does not affect the life of your tankless water heater or the warranty.

The water is pumped more quickly than if you ran the faucet full throttle. You save time, water, energy, and money!

There are at least three manufacturers of demand systems, Metlund, RedyTemp, and Chilipepper. The Chilipepper will run any tankless water heater. Some models of the Metlund system will run tankless water heaters, and some won't, so be sure to inquire before you make a purchase. The RedyTemp will not work with a tankless water heater.

Choose the type of system that best suits your needs and enjoy the added convenience of quick hot water while being kind to the planet.

For free information about water heaters and hot water circulating systems, visit Mr. Lund's website: All About Water Heaters Mr. Lund also has a website for information about making money online: Lund One - Make Money Online

Ten Tips to Create Excitement in Your Bath

A boring bathroom is not the end of the world. It functions well, it serves all of its purposes, but your bath should be a pleasant room to use. You need to stop thinking about bathroom vanities and bathroom mirrors as things that are not stylish and start realizing that your bathroom has the potential to be something better than you could ever image. Here are ten ways that you can turn your bathroom from blah to wow.

1. Bathrooms should be personal. When you are looking for a way to add pizzazz to your bathroom, remember that your family will be the ones that use it primarily. As such, why not add some personal mementos or pictures on the walls? They can create interesting focal points as well as design pieces.
2. Shelving can be art. Instead of relying on bathroom mirrors and bathroom vanities to be the central pieces, you can add a singular shelf to the wall, place a few decorations on it and really turn your bathroom around.
3. Bring in a chair. If you have a larger bathroom, you are probably not using all the space you have. Try bringing in a chair or small table to add some interesting features. You can then decorate the table with something that relates to your dcor.
4. Think about adding flowers. By adding fresh flowers to your bathroom at regular intervals, your bathroom will always seem fresh and exciting. You might want to choose only flowers that are in season for a constantly rotating display, even bringing in seasonal plants for the holidays too.
5. Change your ideas on vases. You do not have to use a boring glass vase to hold your flowers. Try to use things like watering cans and interesting pieces of pottery to change up the room and expand upon a theme.
6. Look at your bathroom mirrors. If you are creative, you can add frosted detailing to your mirror for a new twist on your design. Simply go to your local crafts store to find the materials that you need as well as design stencils that will help you be consistent with the frosting. If you ever tire of the design, you can always remove it and replace it with something new.
7. Change your bathroom vanities. By stripping the bathroom vanity and replacing the finish with stain or another color of paint, you will dramatically change the appearance of the room.
8. Replace your drapes or blinds. By changing the window dressings, you can create a new look to your overall bathroom interior. Change metal mini-blinds to wooden blinds or take them away to replace with gauzy sheets.
9. Take away anything that does not belong in the bathroom. This seems like common sense, but when you want to spruce up your bathroom; you need to take away anything that might be causing it to look too utilitarian. For example, remove the litter pan from the bathroom and find a new home for it.
10. Change everything twice a year. If you just do not know what to do with your bathroom, commit to making one simple change twice a year. This will help you continuously update your bathroom mirrors and bathroom vanities without taking a lot of time or money.

Dave Robert is a VP at Discount Bathroom Vanities Publishing, and an avid fixer-upper who's been restoring old houses for more than twenty years. Readers can tap into Dave's knowledge about home remodeling, and kitchen and bathroom design, at: http://www.DiscountBathroomVanities.com

Squeeze Page - Straight Or Reversed?

The other day, not too long ago, I was asked, whether a squeeze page or a reverse squeeze page performs better for generating opt-ins for a promotional type of email newsletter.

Of course my answer was, "It depends".

But let me start slowly here and tell you about some history first before I will explain what a squeeze page and what a reverse squeeze page is.

Squeeze Page History

The traditional squeeze page is said to be invented by Eben Pagan, who has become a perfect role model for the typical Internet marketing success story. Eben's original idea was to tease Web visitors with valuable information, but not giving it to them directly. Eben was the first one who asked for an email address in exchange (or the first one, who became famous for it).

I think it is important to note that we are not only talking about generating a list of email addresses here. The ultimate purpose is to sell valuable products. Preferably it should be your own product or it could be an affiliate product as well.

A little detour: You can make a good living from promoting affiliate products, but did you ever wonder, why so many successful affiliate marketers start selling their own "How to make money... " product at a later point in their career. The reasons can be summarized real quickly, but that actually exceeds the scope of this little treatment here:

• instead of working as an affiliate, you have affiliates working for you
• your product, your terms
• even more money
• independence

The Purpose Of A Squeeze Page

The point is, online marketers have learned -- as direct response marketers have learned before them -- not everyone who reads a sales message or advertising for the first time will buy the promoted product right away. You cannot just let them leave. The modern squeeze page on the Web resembles the post card attached in magazine ads. It's the same mechanism. The advertiser or Web site owner promises something that is useful for the readers. They will get it in exchange for their contact information.

Back then, when Eben had introduced this direct response concept on the Web, it seemed quite revolutionary and bold, because everybody thought all the information on the Web were free to access. Breaking that believe, made Eben succeed with his product in the dating niche.

It is reported that it takes 7 visits to a vendor's Web site on average before a prospect buys the featured product. An email list generated from a squeeze page shall make sure that the prospects indeed are there, back on the site, again, and again,... till they buy or opt-out. An email list makes its owner more independent from paid sources of traffic to their Web site. (Let's be honest here, even so-called "free traffic" costs money, unless one values time with 0.00$ an hour.)

Especially new online marketers forget the real purpose of their email list very quickly after they have started it. They very often fall back into the believe that those people want to hear from them. The truth is, when they signed up, they wanted the cure for their problem, otherwise they wouldn't have signed up to the list. They only care about what you have to say, what you have to write as much as it helps them to solve their problems. That's copywriting 101, isn't it.

That said, it makes sense to trade valuable information that helps your visitors with their email address. This allows you to stay in touch. That's exactly what the original squeeze page does.

After talking about the background of squeeze pages a bit, let's look what a squeeze page is

The Traditional Squeeze Page

• A single Web page that offers specific, valuable information to a certain group of people, like an ebook "How To Get Rid Of Back Pain Forever". It is important to drive targeted traffic to that landing page. In many cases this page will be the home page of a domain, like www.cureyourbackpainforever.com (That domain is actually a real one, but only parked, not being used.)
• The only 2 actions a visitor can follow are join the newsletter or leave.
• The copy on a squeeze page shall be persuasive, create trust and highlight the benefits of opting in. Most marketers have started to incorporate audio and video messages to make the sale on their opt-in form. There is a strong call to action.
• Some marketers even put opt-in forms in front of their sales letters. That means you cannot even buy the product before making the first step of giving away your email address.

Many people -- consumers and business owners -- feel that's going too far, they refrain from filling out such a from respectively refrain from using a traditional squeeze page on their sites. That brings us to the next step.

The Reverse Squeeze Page

It follows the same principle, but will allow the visitor to consume a chunk of free information, before they need to provide their email address. At the end of those messages, they will generally be told that there is much more free, valuable info in store for them, if they sign up.

Typically you would see it implemented like presenting a free report for download right away, or more recently a free video. At the end will be the call for action, "You like my info? Now, sign up to get more of it ...".

The difference between the reversed squeeze page and to a normal sign-up form on a Web page or a Blog is that the possible actions for the visitor are still very limited in case of a reversed squeeze page. It's about signing up or not signing up.

What works better

As I said in the opening, "It depends!". You need to test it for your market, for your audience, for your traffic sources. That's the only way, you'll know.

You can always check what type of squeeze pages are common in your market and start out with that model, but you might find that squeeze pages are not so common outside the "Money Making Niche" at all. In that case just introduce them.

The author John W. Furst provides first class articles and information about every aspect of Internet business and personal development on his Blog. His writings are the essence of 15+ years of experience with business in general and Internet in particular. Recently Mr. Furst shifted his focus towards Email Marketing. Read more at his E-Biz Booster Blog at http://blog.fcon21.biz and check out the Email Marketing Tips Blog Carnival

Why Hire a Paint Contractor - Home Remodeling

Often the best option a homeowner will have when remodeling their house is to hire a contractor to do the work for them. This way they will get professional work at a good price and will not stress over the project, as many homeowners choose to do the work themselves and find themselves stressing out over it. When the homeowner is left to relax or focus on other projects, they often feel good about the remodel and the experience becomes a positive one.

A paint contractor is trained thoroughly in the craft of exterior painting and is motivated to provide their clients with the best work possible. This often translates into an excellent finished product that the homeowner can be proud of. Not only will the project go by quickly, but the homeowner will sacrifice no quality with the hastiness a paint contractor can finish the project. Being experienced in the field, contractors are skilled at finished the project in a timely manner and with excellent craftsmanship. Homeowners are happy they called a contractor, as many have had negative experiences when trying to take on large home improvement projects alone.

When the homeowner goes at it alone, they often sacrifice the finished product. While they may enjoy the outdoors and working with their hands, what they get in the end is seldom worth the perks exterior painting may offer some homeowners. Even if they get the chance to bond with friends and relatives while they assist them in their remodel, being unsatisfied with the final product often does not make the experience worth it. The finished product is usually what the homeowner cares most about, so this is what should be considered when considering the options the homeowner has for exterior home painting.

Many paint contractors offer homeowners with affordable work that will leave them completely satisfied. Homeowners go into a project with a vision of what it will look like when finished. When the final product is far from what they had envisioned, they often feel unsatisfied or annoyed. The closer it is to what they had imagined, the more pride they will feel. When homeowners are left to their own devices, they often come up short of what they are striving for. A contractor often is the key to getting what they want and finding a formula that works for the project.

Realizing the value of a paint contractor is often the first step in hiring their services. Professionalism brings a good deal of confidence to the jobsite, confidence that often means excellent craftsmanship and beautiful results. Not only do homeowners get to rest easy knowing their project is in good hands, they are also able to focus their attention on projects that may require less professional attention. This can make a remodel move faster or can allow the homeowner to save money in other areas that may not be so complicated that they require the work of a contractor. The benefits a paint contractor brings to the jobsite are enormous and homeowners should surely take advantage of their skill.

More information on http://www.ultimaterollercoaster.com/resources/college-works-painting/ College Works Painting is just a click away.

Transform Your Bathroom - Home Tips

When you don't have room in your budget to completely renovate your budget, it is amazing what installing a new bath vanity will do for the look and feel of this room of your home. The simple task of changing the cabinetry in the bathroom will make it look as if you have redone the whole room. Simply adding a few different accessories, such as changing the color of the towels of the shower curtains will enhance the effect.

A bath vanity does not have to be an expensive proposition with the many styles of discount vanities available. You do have to look at the size of your bathroom so that you get a vanity that will suit the space you have. For example, adding a large vanity to a small bathroom will make the room look crowded.

The vanities available in MDF are not expensive and require assembly. However, the detailed written and visual instructions that are included will make the assembly quite easy. Even the tools you need to put the various pieces together are included. All you have to buy extra is the sink and countertop, but there are some models that have this included as well.

The bath vanity is the central focus of a bathroom. This is where you will spend time grooming yourself in the morning before you go to work and when getting dressed to go out at night. You do need to have drawers and shelves where all your grooming aids are close at hand.

You can blend the old with the new by using an antique style that has a wash basin type sink that sits on the countertop. You can choose from a wide variety of colors, but the best rule of thumb to follow is to have a vanity that is of a neutral color. You can add contrast in the faucets and colors of linens that you use.

You do have to make sure that the bath vanity of your choice is sturdy and durable. You will not save any money by buying a vanity that is really cheap only to find that you have to replace it in a few years. A lot of the furniture manufactured today is eco friendly using glues that will not emit any harmful fumes into the air when they come in contact with water.

Even the smallest bathroom can have an elegant bath vanity or even a glass sink. A stone vanity, for example, can measure only two feet wide and will make a bold statement in your bathroom as well as make it look larger than it is. A vanity made of stone with teak cabinetry inserted in the center is also a viable option if you are looking for durable construction that will last for many years to come.

When you shop for a new bath vanity you can do so in many different ways by focusing on any of the following aspects:

Size

Shape

Material

Price range

Obviously the price will be the bottom line for you, but you will find that there are vanities to suit every taste. Browse the sites of the many online retailers just to get a glimpse of the wide assortments you can choose from. This will give you ideas to work with when you are contemplating making changes to your bathroom.

Allison Ryan is a freelance marketing writer from San Diego, CA. She specializes in home remodeling and interior design. For a beautiful bath vanity or glass sink for the bathroom of your dreams, please visit http://www.mybath.biz/.

Home Termite Repairs

Garage Conversions - Safety and Value Issues for Real Estate

Occasionally a garage conversion will be carefully done so that the exterior of the conversion closely matches and harmonizes with the rest of the home. The only giveaway is the presence of the driveway leading right up to the home. The quality conversion interior will be on par with the rest of the home, be adequately insulated, heated and cooled and will feature adequate windows and an exterior door to allow natural light, access and ventilation. By contrast, the cheap conversion will have few or none of these amenities.

Safety is a prime concern due to the possibility of fire. A garage conversion with no windows or exterior doors is a fire hazard since anyone caught in that area when a fire blocks their way into the rest of the home can be killed. And since garages are very often adjacent to the kitchen where most fires begin, the potential for disaster is very real and every second counts. Each room in a home must have a way to escape a fire. At a minimum, there must be a window that can be easily opened and is large enough for an adult to slip through in a hurry. A door opening to the exterior is a prudent addition.

An additional consideration is the quality of wiring and the type of heating in the garage conversion. Faulty wiring and/or unsafe use of appliances can start a fire. Free-standing unvented "space" heaters pose a threat from carbon monoxide poisoning.

A garage conversion creates a lack of covered parking space and usually results in decreased storage space. Only when the site is large enough, and building setback lines do not interfere, can additional covered parking be physically and legally provided.

Value Considerations Stemming from the Above

It stands to reason that a good quality garage conversion will bring more value to a home than a cheap one will. The very cheap conversion where the overhead doors have been blocked off and some inexpensive floor coverings added is probably best converted back to garage space, since the cost should be minimal to once again offer a garage. This minimal restoration cost can be offered as a price concession if the owner is unwilling to make the restoration prior to closing. But even the good quality conversion poses the problem of a lack of covered parking if a separate garage structure or at least a carport is not present. The owner and agent should anticipate a reduction in value for this factor. How much reduction to expect is a matter of patient research.

A garage conversion should always be inspected carefully by a qualified real estate inspector, and this will normally be included as part of the whole-house inspection process. In Texas, such inspectors are required to be state licensed. Such an inspection should reveal health, safety or structural problems and the cost to do the repairs can also be offered as a price concession unless they become a lender requirement as a condition of making the loan.

Harry E. Davis is a Texas state certified residential real estate appraiser in Texas and is webmaster of the FHA Appraiser Directory Appraiser and appraisals are available at Austin TexasAppraiser

What Kind Of Wood Rot

Hiring a Great Pool Removal Contractor

For some, removing a swimming pool may seem like removing a house. Once you realize it can be done, you may be thinking...but how? How can a huge, concrete based pool that takes up my entire yard be removed safely and efficiently? All kinds of questions may be going through your mind: Will we disrupt the neighbors? How will they get a bulldozer into my yard? What if they hit a gas or water line? Lets face it, fear and anxiety are the emotions we feel when faced with the unknown. These are the emotions that make scary movies, giant roller coasters and haunted houses so compelling, but when you are hiring a pool removal contractor the last thing you want to feel is fear. So how do you handle this process? How do you hire a pool removal contractor in the bay area or anywhere else? The best way to do it is to simply eliminate the unknowns.

When it comes to hiring a swimming pool removal company here is the best advice I can give you: Hire a company that has removed a lot of pools. That's it. It's just that simple. Practice really does make perfect. Plus, there's a reason why a particular contractor has done a lot of work. People trust them - they have a track record. It's no different than if you needed brain surgery and you were interviewing surgeons. If the doctor told you it would be his first, but another other one had done a hundred procedures, who would you pick? You'd probably be concerned about the outcome if you chose the first doctor. Same goes for pool removal. Pick a contractor that knows their stuff!

So, you have started the search. You are calling contractors and talking to friends. How much experience should your pool demolition contractor have? One hundred pools or more certainly would be a high benchmark. If a company has removed that many swimming pools, they understand all the pitfalls and problems that can arise. That makes it much more likely your job will get done right and in a timely manner. It's an important job, one you want done right. Going with the right contractor could mean the difference between getting it done cleanly and simply in just a few days versus it taking weeks and potential legal hassles. Keep it simple.

Here's another bit of advice: Always check the references of pool removal contractors. People have been getting burned by contractors of all types for years because of not following this step. You especially want to do this if you live in an area where there aren't a lot of in-ground swimming pools. The chances of any one contractor having a great deal of pool removal experience won't be high. The important thing is that you can verify the jobs they have done, and see if their customers were satisfied with the contractors work. Do yourself a favor, check them once and check them twice - call at least 3-5 of their former customers. See what they thought of the work performed. It could save you a huge headache later.

The other thing I always tell people concerns money: Be very leery about giving a contractor money in advance. Did you know that most states have laws about how much money a contractor can ask for up front? Its true. It seems that people have been getting burned by contractors for so long, that the government finally had to step in. If you are serious about your pool removal and want to do it right, you might make it a point to know what your state law is regarding this. Generally, it's a very small percentage of the contract price. In cases where permit fees are high and it takes a long time to get approval, contractors may want the customers to cover those costs. Bottom line: If a contractor asks for a lot of money up front, do yourself a favor: don't do it!

The main point I want to get across is this: do a little home work before hiring a contractor. A pool removal is a big deal. It can be expensive. You really need to ensure that it is done professionally, and at the right price. Whatever you do, don't go with the first bid that comes your way. And if a particular contractor seemed a little shady - trust your instincts, they probably are. Keep looking! When you have confidence that your contractor can deliver, then you can relax and actually enjoy the process. Think about it: your new backyard and new lifestyle are waiting!

If you need help finding a pool removal contractor contact me at verdell@poolitout.com. I would love to help you!

http://www.poolitout.com/

Wood Attic Vents

Moisture Against Gravity - Destroying Walls

Well I'm going to start this article with a little information on a job I did once.

I had been repairing a rental house for one particular homeowner for about three years when all of a sudden I got a phone call from him telling me the rental house was destroyed and he had never seen nothing like this. He sounded so upset over the phone I told him I would meet with him immediately.

On my way to the house I was trying to get an idea in my head what the house was going to actually look like. Since I have been repairing rental properties for over 20 years at this point of my career, nothing really shocked me. I had pretty much seen everything that could possibly be done to rental property by the tenants that lived there. There is a lot to be said about taking care of it as if it were your own.

He was waiting for me at the front door and he looked thoroughly disgusted. As I approached him he was shaking his head and yelling at the same time can you believe these people, can you believe what they did to my house. I was expecting to see the front door ripped off and all the windows broken out of the house but this wasn't the case.

As he led me through the home and I could see the usual clothing on the floor, broken cabinets, a few holes in the walls and of course that awful smell of mold and mildew. All of this stuff was nothing new to me because I'm the guy they call to fix it when a renter moves out of the property.

As I entered one of the bedrooms I got my first glimpse of something I had never seen before but heard stories about and could not believe my eyes. Looking at the walls in the bedroom about 3 feet from the floor all the way around the room, the plaster was soft. It actually looks like someone shoved popcorn into the wall somehow.

The homeowner wasn't even looking at this because of the rest of the damage in the home. I started to explain to him I'd never seen nothing like this but I could guess it was water damage somehow since the plaster was soft. I could actually stick my finger into the wall, that's how soft the plaster was.

My first thought was to examine the carpeting a little closer to see if it was wet. Well it was damp but it wasn't as wet as I would've expected it to be with the amount of water in the walls. With a little more home inspecting I had found the culprit, it was a broken water bed. The water bed was now in the backyard looking innocent.

I couldn't believe a broken water bed could do this much damage so I looked around for broken or leaking water pipes and could not find any. The other bad news I had to inform the homeowner was that the water had damage the bathroom and closet walls also. These walls of course were on the other side of the bathroom walls that were damaged.

Well the point of this story is that water will actually wick its way up or worked its way up into a wall. I had to remove 4 feet of drywall all the way around the room. The plaster or drywall actually acts like a sponge pulling the water into the walls. Hard to imagine that gravity in this case seems to reverse. I would've never thought that water would've traveled so far up the walls creating that much damage.

To repair the rental property I had to remove the damaged drywall, remove the carpeting, dry the wood framing out and put the whole thing back together.

I'm still amazed and will remember that project for as long as I live.

Greg Vanden Berge is working on the internet to promote the education for creating simple to follow guides and home building books to help professional building contractors as well as the weekend warriors. He is currently working on more Building and Remodeling Library and adding useful content to help solve problems created by the lack of construction knowledge in the building industry.

Visit us and get more information on House Water Damage

Roof Truss Repair

Window Screen Repair Video

Great video on how to repair a window screen.

This video was made possible by Greg Vanden Berge who is working on the internet to promote the education for creating simple to follow guides and home building books to help professional building contractors as well as the weekend warriors. He has just finished a home buyers guide to take some of the frustration out of home shopping.

Drywall Joint Water Damage

Ways to Stop Losing Your Car Keys

You obviously don't need to read this article if you rarely lose your car keys. However if you misplace your car keys often and have a pretty good relationship with your locksmith, it's time to change these bad habits into good ones.

One of my friends, recently lost their car keys. I would like you to listen to what I'm about to say and see if it makes sense to you. Most people get two keys when they buy a car. This means, if they lose one key, they now have a spare key. When they lose their first key, this should give them a pretty good clue that the second key is now the only key, if they wish to drive their car.

Does that make sense? If you lose your first key, you don't have a second or spare key anymore. Now is a good time to purchase a spare key or have one made. Don't wait until you lose the second one, unless you are planning to change your bad habit into a good one.

Now let me get back to my friends who recently lost their car's key. The car they were driving was a new Honda and you can't go to the locksmith to get another key made. You have to order one from the Honda dealer and this key cost them over $200. That's a lot of money for one key.

Now my friends lost both of their original keys and now have one key to operate the vehicle and this key cost them over $200. Now if I had to pay this amount of money, I would make sure that I never lost this key ever again. I would do whatever it to to change my old habits and create some new ones.

How hard is it to get in the habit of placing your keys inside of your purse. Placing your keys in your pockets and then only removing them when you are going to place them inside of a drawer, container, cup, bowl or on a shelf in your bedroom. If you place your keys in a drawer, this will keep them out of other people's temptation.

If you choose to lay your keys in a bowl, in the kitchen, there's a good chance someone will take them or another member of your family could lose them. Place your keys in a protected area, do not leave them out in the open ever.

If you want some tips to prevent you from losing your keys, simply talk to someone who rarely if ever loses their keys. Most of these people have simple and easy to follow tips. You can consciously create a habit that can save you money and frustration in the future.

Greg Vanden Berge is a published author, internet marketing expert, motivational inspiration to millions of people all over the world and is sharing some of his wisdom with experts in the fields of writing,marketing and personal development.

Greg is currently working on a spiritual video library filled with great movies on a wide array of topics, like religion, self help and spiritual changes in the world.

Saving Money As A Teenager

Renovate With EIFS and Save $3,000 With the Ontario Home Energy Audit

Ontario's Home Energy Audit provides rebates to home owners who improve their home in some way to reduce energy consumption and waste. The program provides rebates from $60.00 per energy-star qualified window, to $1,000.00 for a high efficiency furnace, to $3,000.00 for insulating the exterior of your home. Why is the largest grant (by category) given to Exterior Wall Insulation? One of the reasons is it can have the largest impact on keeping the heat inside your home as home owners typically see a 20-30% reduction in their heating and cooling bills after renovating the exterior of their walls with EIFS (synthetic stucco).

First Thing is First

In order to qualify for the rebates, you need to first have someone do the Ontario Home Energy Audit. This involves contacting the Government's ecoENERGY program to have an inspector come to your house and evaluate your eligibility. You will fall into various categories ranging from not eligible (because there is nothing that needs to be done), to partial benefits to improve certain aspects, to the full grant for adding something that is not currently there. The majority of homes do not have insulation on the exterior of their homes (from the sheating substrate and outward), which makes most home owners eligible for the full $3,000.00 rebate. From the day of the inspection, you have exactly 18 months to complete all your retrofits and get the auditor back.

Get Quotes For an EIFS Retrofit

It may even be a good idea to do this first so you don't waste time trying to find contractors and prices. It is important to get multiple quotes, from different contractors to get a feel for what the price should be. They can be found via the internet, yellowpages, referrals, or preferably by the EIFS manufacturer who will recommend you to a few contractors they know that do quality work. Speaking with different contractors will open your eyes to aspects others may not mention, such as decorative items or things you need to consider like temporarily removing your soffit. Things that may affect your quotes include:

• Time of year will affect price, which is higher during the winter and busy season
• Not requiring a weather barrier (only if going over brick, concrete or CMU) will save money
• Small portions (such as dormers) often cost extra
• Decorative elements such as mouldings and cornices cost extra

Let's say you understand what your options and prices are after getting 5 quotes, which do you choose? To start, if one is far below the others, toss it immediately. Any money you will save will come back to bite you down the road, and the repair can be more expensive than your synthetic stucco retrofit in the first place. Most of the time you want to go with quote #3 or #4 in terms of price. Don't forget that you can add decorative elements (like window sills, quoins, trim) at a later date -- one of the great benefits of EIFS.

Thickness of Styrofoam

Though this will affect the price and is up to your discretion, a minimum of 2.5" of "Type 1 Expanded PolyStyrene" (the white styrofoam) is required to qualify for the full $3,000.00 rebate. Typical styrofoam thickness is 2", which would get you the $1,800.00 rebate, however the additional 1/2" will not (or rather, should not) run you an additional $1,200.00, which means you will actually save money.

For the technically inclined, a total of R-3.8 to R-9 will qualify you for $1,800.00, while an R-value of 9 or above qualifies for the full $3,000.00 rebate. Type 1 Expanded PolyStyrene (the type of white styrofoam EIFS manufacturers carry and specify) is rated at R-3.71(per inch). This means adding 1" of styrofoam qualifies you for no rebate (yes, they are serious about that 0.09 of R value missing), while 2.5" will qualify you for the whole $3,000.00 (2.5 x 3.71 = 9.275). The other layers of EIFS do provide some R-value (arguable enough that 1" would qualify you for the rebate), however the government stipulates that the R-value is calculated solely on what is added to the wall via styrofoam.

Plan All Your Retrofits, Then Proceed

You want to consider other renovations at the same time as your Synthetic Stucco retrofit. If you intend to add Energy Star qualified windows, they must be installed prior to adding Synthetic Stucco so that they can be properly "tied in" to the wall, that is, to prevent moisture intrusion. You will want to cover these windows while the EIFS is being installed to lessen the chances of them getting dirty. Again, soffits need to be removed during installation to avoid unsightly gaps at the top of your wall which double as a point for water to penetrate. A little bit of planning goes a long way in saving you money and head aches.

Get The Auditor Back

Once everything is finished it's time to have the inspector come back to re-evaluate your home. You will need to show him copies of the bills with the specifications (for example, the EIFS contractor would specify "2.5" insulation added" on his invoice), and pictures of the product being installed may help -- make sure to find out exactly what the auditor is looking for during the first visit. Remember also, that you only have 18 months from the first inspection to get him back, otherwise you forfeit any claim you have to rebates. You may only do this once (ever!) so make sure you do all your retrofits at one time for the rebates, or be prepared to pay for future retrofits out of your pocket.

Upon verification that a minimum of 2.5" of insulation has been applied to all wall surfaces on the exterior of your home, the auditor will check to see if you qualify for any additional rebates for retrofits which may have been undertaken, then electronically submit the result to "Natural Resource Canada" and the "Ontario Ministry of Energy and Infrastructure". From the time your auditor performs the final evaluation, you can expect to wait anywhere from 5-9 weeks for the audit to be processed another 1-2 weeks for the cheque to arrive.

Don't forget that on top of the rebate, renovating your home with Synthetic Stucco increases the value of your home (you recoup up to 88% of the renovation cost via increased home value) and can reduce your heating bill anywhere from 20%-30%, saving you over $500 per year.

Jim Schwarznoff is a Construction Project Management student with an emphasis on the building envelope and exterior design. For more information on EIFS (Synthetic Stucco) and to get quotes from Stucco Contractors visit http://www.TorontoStuccoContractor.com/. For more details on the Ontario Home Energy program, visit: http://torontostuccocontractor.com/blog/2009/01/the-ontario-home-energy-audit-provides-3000-towards-an-eifs-retrofit/

Framing Fireplace Vent

Bathroom Moisture Problems - Home Repair

Right above my bathtub in my master bathroom the paint is peeling off the wall. The area is peeling above the tile in my bathtub and shower combination. I tried to glue the peeling paint back and only made the situation worst.

First things first. The paint is peeling because there is to much moisture in the bathroom while you are using it. Do you have any windows you can open or a ventilating bathroom fan. If you have a window crack it open part way while you are showering.

The water droplets will accumulate on the walls and drip into any cracks. Right above the tile grout is a great place for moisture to accumulate. Oh yeah moisture loves grout and drywall. If you have any unpainted areas or an area that has cracked. Guess what you have now.

Your paint is peeling because the bathroom gets hot and cold. Moist and dry. If you have the door and windows shut. You just created a moisture trap. Most people prefer their privacy and will closes the door when using the shower. Well then open the window and let some cold air in while you are taking a nice warn shower. I don't think so. Most showering fools don't like that idea either.

Ok one more idea keep the windows shut so you don't let the cold air in. Then lock the door so no on barges in on you. If you have a ventilation fan turn it on. This will at least pull fresh air in from under the door and send the moist air out of the house.

But the fan is so noisy and I can't enjoy my nice warm vapor producing shower that will eventually cause me to get sick from mold particles floating around in the air while I am using my bathroom.
Does this about sum it up for you and don't we all do this from time to time. We want to enjoy our shower time, so we close up everything and when we are in our bath sauna environment relaxing our house is getting some damaging moisture that could cause mold and mildew.

Open a window or door a little when you shower. Get some air circulating through the bathroom and prevent damage to your nice house.

Put up with a little inconvenience for you homes sake and your pocket book.

Greg Vanden Berge has been in the home building and remodeling business in California for over 30 years. With this knowledge he has created a few websites that provide useful information for home owners as well as contractors. His main goal is to educate professionals in the home related businesses, dealing with problems that can easily be avoided with just a little bit of information.

His website provides all kinds of answers to remodeling and new house building in North San Diego Home Remodeling Carlsbad Home Remodeling

Visit us now for Bathroom Ideas

Magical Numbers

Why You Should Think Twice Before Using Reverse Osmosis Home Systems

Are you using reverse osmosis home systems or are you thinking of buying one? If so, please take a moment and read this article. This article will help you avoid making a mistake that a lot of people make when it comes to choosing a good water purifier.

Millions of people drink reverse osmosis water every day thinking it is pure and safe. How many of these people looked beyond the marketing hype and investigated in depth how a typical unit works. The truth is - it is not suitable to be used as a drinking water supply.

A reverse osmosis unit consists of a semi permeable membrane and water is passed through the membrane under pressure. Theoretically when water passes through the membrane, any particle that is larger than water molecule in size will be blocked. As a result, you should get pure water to drink. In practice the results are slightly different. The water you get from an RO unit is neither pure nor safe to drink for two reasons.

1. Reverse osmosis home systems are not capable of blocking any contaminant that is smaller in size than the water molecule. As a result, the water you drink might still have contaminants like herbicide traces which are smaller than water molecule in size.

2. The reverse osmosis water you drink is not healthy either. During the purification process, the essential minerals and nutrients tend to get destroyed. These minerals, as the name suggests, are very essential for various biological functions. Without these minerals, the water you drink is only as good as the distilled water which is used in car batteries.

Just think about it for a minute or two. The water you get from an RO unit is not completely pure. It is not healthy. The unit tends to waste a lot of water. And most importantly, it is expensive to set up an RO unit in your home. Shouldn't you think twice before using this kind of a water purifier?

The solution, fortunately, is available easily. Go for a good purifier with active carbon filters. This ensures two things. First - they are capable of removing all types of contaminants present in water. Second - they do not destroy the essential minerals present in water. Also, if I may add, they are cheaper than reverse osmosis purifiers.

So you know what the problem is and what the solution is. All you need to do now is - take action. Avoid reverse osmosis home purifiers and get a good, effective water purifier today.

Derek Reeve runs an informational website that provides details of the best home water purifiers. If you're serious about improving the quality of water you use visit water purification systems for home to find the most effective,efficient and affordable products available.

Stucco Stain From Roof Leak

Credit Repair Techniques That Are Effective

The ultimate goal of credit repair is to be able to qualify for all types of consumer credit with the best financing terms and the only way to accomplish this task is by using credit repair techniques that are effective.

In this article I will go over a few effective credit repair techniques.

The first effective repair technique I want to go over is establishing new credit accounts. Some people don't regard this as credit repair but the truth of the matter and a little known secret is the fact that you cannot fix a poor rating without re-establishing new credit accounts.

A significant amount of what goes into calculating your credit scores is based on accounts that are current and in good standing and the only way to have these on your report is to re-establish new ones.

Your credit report also contains a lot of personal information about you such as your most recent address and employment address. Make sure all this information is up to date and accurate...No one knows the exact criteria the agencies are looking for so you want to make sure there is not any inaccurate data reporting on your file.

The same goes for revolving and installment credit accounts such as credit cards and personal loans, if you are not familiar with them, you want to dispute them to have them deleted ASAP!

Negative revolving and installment accounts that you have not made payments on in seven years should also be deleted from your account according to the law. But remember that the credit bureaus don't always do this automatically so you need to act!

Visit do-it-yourself-credit repair or credit repair services to learn more on raising your credit score 200+ points to get approved for car, home and credit card loans.

Drywall Termite Damage

Concrete Foundation Crack Repair

Foundations made of concrete can crack as a natural process of it curing. These cracks are called shrinkage cracks. As the name suggests, concrete actually shrinks as it cures. This shrinkage builds up stress and the concrete must crack to relieve the stress. While they are a normal condition for a home's foundation, foundation cracks can let water leak into the basement.

Water that gets into the basement can damage carpets, insulation, drywall and the homeowner's possessions. That is why before you begin an expensive remodeling of your basement, you should make sure that the foundation cracks do not leak.

Homeowners traditionally had to call professional waterproofing contractors to chisel out a vee-notch in the concrete wall and fill it again with hydraulic cement. The hydraulic cement would temporarily fix the leaking problem. Unfortunately, as water enters the crack and evaporates out into the basement, salts dissolved in the water are left behind. Eventually these salts build up and cause the bond of the hydraulic cement and concrete foundation to fail. The hydraulic cement cracks let water back into the basement.

Now homeowners and professionals can repair the concrete foundation leak with a liquid urethane injection process. The urethane is injected directly into the crack in a liquid form. The urethane begins to foam and expand inside the crack. This expansion fills the crack from top to bottom and from front to back. Once completed, the foundation crack will not let water into the basement. Also, the repair gives a long life because water cannot enter the crack and deposit salts and cause a failure of the bond between the foam and concrete foundation.

This article is written by Aaron Kuertz with Applied Technologies. Aaron has been in the waterproofing industry since 1998. Applied Technologies is a manufacturer and supplier to professional waterproofing contractors and homeowners in the United States. To learn more about concrete foundation crack repair visit Applied Technologies on the web.

Wood Rot From Stucco

Home Contractor Problems and Solutions

This is one of the biggest problems in business today. You have some work done on your home in good faith that the contractor knows what he is doing. When all is said and done you have a problem that needs to be resolved as soon as possible. I really don't care how long it has been since the work was done. If you have a problem the least that your contractor can do is answer the telephone.

Some companies go out of business and others get to busy to respond to your problem. You will hear the old excuse "That's not my problem" or the ever popular " I didn't do that". I have been in business for over twenty years and had very few problems. Of course I built things to last as long as possible.

Keep in mind that some contractors are a one man operation and they might be on vacation. Some contractors do not answer their phones over the week ends or after business hours. So don't sink the ship to fast.

Do not call the Contractors Licensing Board or the Better Business Bureau unless it has been at least a few working days. I would give it at least a week or so. Oh yeah don't assume that the contractor got your message. Call a few times at the least.

It has always made me mad when I have to fix someone else's problems. I get the call when the other contractors won't respond. I listen to the home owner with regret for being in a business where I am considered a crook. This is one of the reasons why contractors in my business get out of it.

If you have the contractors address and they aren't responding by phone you can always send them a letter by certified mail. Request a return receipt. That's your proof that the company received your letter. Keep a copy for your files.

The good news for a home owner when a contractor will not respond to your calling them is the Department of Consumer Affairs. Most states have a complaint department of some sort that will listen to your complaints. Does this mean it will get resolved? NO there are no guarantees here.

If your state has a licensing board for contractors, this will be your next step.

This will get your contractors attention and there is a great chance they will respond now. If there are enough complaints against the contractor and they do nothing about them the contractors board will take their license away.

If your contractor does not respond after all of this. There is very little you can do about it. Hire someone to fix the problem and look at it as a very important lesson learned.

If your state doesn't have a contractors licensing board contact the Better Business Bureau or your local government for their recommendation. Ask some of your friends if they have had any problems like this and how they handled them.

For some more tips about hiring contractors go to
http://gregvan.com/library/homeowner_checklists.htm

Greg Vanden Berge has been in the home building and remodeling business for over 30 years. With this knowledge he has created a few websites that provide useful information for home owners as well as contractors. His main goal is to educate professionals in the home related businesses, dealing with problems that can easily be avoided with just a little bit of information.

His website http://gregvan.com provides all kinds of answers to remodeling and new house building issues that could create major damage as well as possible damage to your pocket book.

Easy Build Stair Handrailing Video

Stair building tips for installing lights and decking, handrail tips and some deck advice.

For more helpful home improvement information visit: http://www.gregvan.com

Stair Building Help

Exterior Siding
Caring For Your Vinyl Siding

Wood Beam Repairs - Home Repair Tips

If you live in a moist climate in the winter and a dry climate in the summer and you have exterior wood beams exposed to these elements. You could develop wood beam problems over time. If wood beams are properly maintained and painted often they could last for a long time. Wood beams can last many years if properly taken care of.

Exterior wood beams that are used to hold up roofs, patios and decking can suffer from wood rot if not taken care of. Let's take for example a wooden beam located in a patio holding up a section of a large roof. The span of the roof being is only 10 feet long. As we look at the exterior wood beam. We noticed the upper corner of the beam is soft and rotted.

The beam damage is roughly the size of a baseball. The wood beam itself is a 6 x 10. Do we need to replace this beam even though the damage is not real big. The answer to this question is yes, any amount of damage to a wood beam takes away from its structural strength.

If you have a wood beam holding up the roof and the beam fails you could end up replacing a large section of your roof as well as the damaged beam. Replacing the damaged beam is usually a difficult task. The beam is usually sandwiched between two walls and will have siding or stucco around it.

If you're lucky enough to have the wood beam sitting in a saddle or on top of a wood post this will make your job easier and will require less skill. If however the beam is located between two walls this will require shoring up the roof and removing the beam.

Beam replacement should be left to professionals. This is not often as easy as it looks and could create a safety hazard if not done properly. I have seen beams replaced by homeowners or handyman and the damage that was done after the repairs, was worse than just leaving the beam alone in the first place.

The biggest problem with exterior wood beams is that they are usually holding up large amounts of weight. If the beam is removed without the proper bracing and shoring of the roof or floor area you could have a larger problem than you started with.

Exterior beams over time seemed to develop large cracks or splits in dry weather. These large cracks and splits weaken the structural strength of the beam adding more stress to the beam itself leading to structural failure eventually.

Extreme climates where temperatures very over 40 in one day seem to suffer the most damage to exterior wood beams that are not properly maintained. Beam maintenance will require painting and keeping moisture away from them.

Be aware of structural beams in or around your house. A little painting now and then can save you thousands of dollars over the life time of your house.

Greg Vanden Berge has been in the home building and remodeling business for over 30 years. With this knowledge he has created a few websites that provide useful information for home owners as well as contractors. His main goal is to educate professionals in the home related businesses, dealing with problems that can easily be avoided with just a little bit of information.

His website http://gregvan.com provides all kinds of answers to remodeling and new house building issues that could create major damage as well as possible damage to your pocket book.

Visit us now for Vista Home Improvement.

Dust Clogging Bath Fan Vent